Arai Regent-X Full-Face Helmet | Gear Review

Arai Regent-X Helmet
Arai Regent-X in Sensation Yellow Frost

Arai Helmets’ premium full-face and open-face motorcycle helmets stand out for a lot of reasons. Chief among them are impeccable hand craftsmanship and materials, comfort, a custom-like fit and an unwavering devotion to the company’s stringent definition of head protection, which generally exceeds U.S. Snell certification standards. These qualities have helped Arai build a large fan base among both regular on- and off-road riders as well as a heap of successful racers.

That base might also point out that — because of all of the above — Arai helmets tend to be pricy, and for some wearers the design of the shell, neck roll and cheek pads can make the helmets difficult to put on and take off. Once an Arai is on your head, it’s hard to imagine a cozier, more secure lid, but for some getting it over the largest part of their melon can be a struggle.

Regent-X more room
The Regent-X is easier to put on/take off, thanks in part to a newly shaped shell with a 5mm wider opening in the cheek and chin areas.

To address both issues Arai has created the new Regent-X full-face helmet, which offers all of the qualities for which Arais are known at a lower cost, and it has some simple changes that make the Regent-X lighter and easier (effortless, actually) to slide onto and off your noggin. For starters the Hyper-Ridge-reinforced bottom opening of its new Peripherally Belted – Complex Laminate Construction 1 (PB-CLC1) fiberglass shell is 5mm wider in the chin and cheek area, and the neck roll is thinner and shorter back to front. Arai’s Facial Contour System (FCS) cheek pads, which move up and down as you don the helmet and wrap snugly around your jaw, carry over but now have recessed speaker pockets for more space and to ease communicator installation.

More cost-effective materials make the Regent-X’s new shell a little heavier than the PB-SNC2 shell in Arai’s flagship Corsair-X helmet, though Arai says it still provides the same level of protection. Interestingly, at 54.5 ounces in my size large, due to its minimal vent scoops and simpler neck roll the Regent-X ends up 2.5 ounces lighter overall than a Corsair-X. As usual the Regent’s brushed nylon interior is soft and silky comfortable, and optional sizes are available for the removable, washable head liner and cheek pads for a custom fit. Venting is noticeably effective and the front chinbar and dual brow and top vents are closable, though the rear exhaust vents on the Regent-X are always open.

Arai cheekpads
FCS cheekpads rotate slightly when donning/doffing the helmet to facilitate a more comfortable experience.

A few years ago Arai changed its toolless shield pivot design to make it easier to use and enlarged the smooth area above it (along the Snell impact test line), so changing shields is a snap (as always, read the manual). I’m a big fan of Arai’s ProShade shield, too, which adds a flip-up sunshield to a regular clear shield to provide similar convenience to an interior drop-down sunshield without compromising the forehead area of the helmet.

If you’re a regular Arai wearer you’ll find the Regent-X so easy to slide on and off that it actually takes some getting used to, but once you do I promise it will become your go-to Arai, especially since it’s just as quiet, light and comfortable as other Arais. 

Regent-X's newly shaped shell.
The upper edge of the Regent-X’s eye port is reinforced with Arai’s Peripheral Belt, which is custom woven in-house with proprietary super fibers to increase shell strength without adding thickness or weight.

The Regent-X has an Intermediate Oval interior shape (Round Oval and Long Oval are available in other Arais), is Snell M2020 certified and will be available in early to mid-December in a variety of solid colors ($559.95) and graphics ($689.95). 

For more information, see your dealer or visit

Arai Regent-X Helmet
Arai Regent-X in Sensation Red Frost


Please enter your comment!
Please enter your name here